Medisafe Sonic Irrigator “Automatic”- floor model cannulated instrument-cleaning system, for cleaning cannulated instruments both inside and out, in a fully validated, clinically tested process.   

Our system combines: Automatic fill, pre-washing, auto enzyme injection, ‘pulsed’ sonic-flushing wash,‘pulsed’ sonic-rinsing, auto instrument lubrication, auto drain.  Cleaning up to 18 instruments at temperatures up to 130ºF both inside and out, in a fully validated automatic process taking approximately 35 minutes per cycle.   Multi variable programmed cycles can be preset for operator convenience.

Special plumbing/drainage required and is responsibility of purchaser (call for installation specifications) standard 110v electrical required.  
 

6.6 gal tank size

43.5” length x 19.5” width x 44.0” high
(add 15” with lid open).

For optimal cleaning performance use recommend 3E-Zyme Triple Enzyme Cleaning Solution  (#MEDIS-12041)

Specifications

Sonic Irrigator –Auto   #MED1157S

Quality

Manufactured in the UK under Medisafe’s IS09001 Quality

Use

For internal and external cleaning of cannulated / lumened surgical instrumentation

Environmental

For indoor use at altitudes up to 2000m / 6000ft
Operating temperature -5°C / 23°F   to   40°C / 104°F
Humidity -80% RH max for temperatures up to 31°C / 88°F,
decreasing linearly to 50% RH at 40°C / 104°F
Designed for Pollution Degree 2, i.e. not totally sealed.

General Description

Medical Device Class I

Operating Process

Ultrasonic activity plus CPE

Applied Standards

BS2745: part 1: 1993
BS2745: part 3: 1993
EN60101-1:2001 (2nd Edition)
EN61010-2-045 (2001)
EN61326: 1997
A1: 1998
EN980

            
Wash Cycle Parameters

Min. Temp. During Cycle: determined by temp. of water supply
Max. Temp. During Cycle: 60° C / 140° F

Vol. of Dispensed Chemicals

Wash chemical: Detergent 160ml / 5.4oz (approx)
Final rinse chemical: 160ml / 5.4oz (approx)

Electricity Supply

110v AC 50 / 60Hz
Power Consumption: 0.8KVA max.
Termination: 3-pin type earthed plug (fused @ 13A if UK)
Lead Length: 1.83M (6 feet)

Printer

Supply Voltage: single phase 110v 0.1 amps (nominal) AC

Required Utilities

Water Supply

Cold water supply terminating into a Male ¾” NPT National Pipe Thread hose  fitting

Hot water supply terminating into a Male ¾” NPT National Pipe Thread  hose fitting. 

Optimum pressure: 1.5 BAR (22 PSI)

Acceptable Pressure Range:
1.5 – 2.5 BAR (21 – 35 PSI) hot & cold

Acceptable Temp. Range:
Hot:  55°C /  141°F   - 75°C / 167°F
Cold  5°C  / 41°F– 25°C / 77°F  

Hardness CaCo3:
not more than 115 ppm (HTM2030)

Drain

Discharge Orifice Type: 18mm outside dia.
unthreaded hose tail

Position of drain: at least 150mm below rear drain outlet

Max. Flow to Drain: 20 liters / 5.3 gal min

Max. Temp. of Effluent: 60° C / 140° F.

Ventilation

Max. Heat Output of Load: 60° C / 140° F

Weight & Dimensions

Operational weight: 60.5kgs / 133.3lbs

Dimensions: Wash Chamber Volume: 27,000 cm3

Outer Cabinet Dimensions:  43.5”  (w) 18.5” (front to back)
add approx 6” for plumbing outlet 44.5” (h)
add approx 15” when lid fully opened